ESP32-EVB Rev D - ethernet: no ip, no connection

Started by meyer, June 12, 2018, 05:52:20 pm

Previous topic - Next topic

meyer


Hi,

I just got the new Rev. D from ESP32-EVB. I was running the ethernet_example, ota_example etc. successfully on the ESP32-EVB Rev. C. The same code does not work on the Rev. D.
emac is saying "eth link up"
esp_eth_init and esp_eth_enable both return ESP_OK
In case I enable DHCP, the device does not get the event that an IP was assigned.
In case I set a static ip, the ip can be read out with tcpip_adapter_get_ip_info,
but I cant do any connection.
I looked into the code on github from Olimex, but I can't find any difference for the Rev D.
Do I have to change some params? Or is there any other difference?
I used the esp-idf release 3.0 from 24th of April

my config:
CONFIG_PHY_TLK110=
CONFIG_PHY_LAN8720=y
CONFIG_PHY_ADDRESS=0
CONFIG_PHY_CLOCK_GPIO0_IN=y
CONFIG_PHY_CLOCK_GPIO0_OUT=
CONFIG_PHY_CLOCK_GPIO16_OUT=
CONFIG_PHY_CLOCK_GPIO17_OUT=
CONFIG_PHY_CLOCK_MODE=0
CONFIG_PHY_USE_POWER_PIN=
CONFIG_PHY_SMI_MDC_PIN=23
CONFIG_PHY_SMI_MDIO_PIN=18

I hope someone can point me in the right direction.  :)

greetings, Frank

LubOlimex

Technical support and documentation manager at Olimex

meyer

Hi, thx for the answer,
yes I tried the example from Olimex, I compiled it with esp-idf with tag v3.1-dev v3.0-rc1 and v3.0 and of course master. I tried it on win 10 with msys and on mac.
In v3.0 the Lan LEDs are constantly flickering, master looks better, but also no ip and no connection with static ip. (tested in 2 different networks)

I also tried with the ethernet example from the esp-idf.
The Rev C Board ist working with the very same image.
I have 2 Rev D Boards and testet with both.
I think the only change that is relevant between the revisions is the 1k resistor R57.
And its connection to OSC_DIS. What does the name stand for, an oscillator?

greetings, Frank


output:

I (263) cpu_start: Pro cpu start user code
I (281) cpu_start: Starting scheduler on PRO CPU.
I (0) cpu_start: Starting scheduler on APP CPU.
I (284) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE
I (284) emac: emac start !!!

I (294) emac: emac reset done
I (524) emac: emac start success !!!
I (4524) eth_example: ~~~~~~~~~~~
I (4524) eth_example: ETHIP:0.0.0.0
I (4524) eth_example: ETHPMASK:0.0.0.0
I (4524) eth_example: ETHPGW:0.0.0.0
I (4524) eth_example: ~~~~~~~~~~~
I (4534) emac: eth link_up!!!
I (6524) eth_example: ~~~~~~~~~~~
I (6524) eth_example: ETHIP:0.0.0.0
I (6524) eth_example: ETHPMASK:0.0.0.0
I (6524) eth_example: ETHPGW:0.0.0.0
I (6524) eth_example: ~~~~~~~~~~~

...

LubOlimex

Frank,

Can you tell me if the problem persists after using the reset button?

The issue doesn't appear with our production tests (which include Ethernet test) so I guess there is some software fix or workaround but we have to investigate further.

Best regards,
Lub/OLIMEX
Technical support and documentation manager at Olimex

meyer

Hi Lub,

yes the problem persists, after several resets it is not working,
plugging ethernet cable out and in is also not working. (eth link up and eth link down is shown)

I have just pulled the esp-idf and the Olimex ESP32-EVB repo.
I ve seen that the last commit was named "Update for idf 3.1", but I think v 3.1. is outdated from Decembre 2017. but i guess 3.0.1 was meant.

On compiling I just acknowledged the default options for the esp-idf config.

I had a look at the R57 as it is a change from Rev B to D.
On my boards there is no 1k on R57, there are just two solder joints.
Is that correct? Or do I have to add a 1k there?


Output:


I (286) cpu_start: Pro cpu start user code
I (304) cpu_start: Starting scheduler on PRO CPU.
I (0) cpu_start: Starting scheduler on APP CPU.
I (307) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE
I (307) emac: emac start !!!

I (317) emac: emac reset done
I (567) emac: emac start success !!!
I (4567) Olimex_ESP32_EVB_REV_B_eth_example: ~~~~~~~~~~~
I (4567) Olimex_ESP32_EVB_REV_B_eth_example: ETHIP:0.0.0.0
I (4567) Olimex_ESP32_EVB_REV_B_eth_example: ETHPMASK:0.0.0.0
I (4567) Olimex_ESP32_EVB_REV_B_eth_example: ETHPGW:0.0.0.0
I (4577) Olimex_ESP32_EVB_REV_B_eth_example: ~~~~~~~~~~~
I (4587) emac: eth link_up!!!
I (6577) Olimex_ESP32_EVB_REV_B_eth_example: ~~~~~~~~~~~
I (6577) Olimex_ESP32_EVB_REV_B_eth_example: ETHIP:0.0.0.0
I (6577) Olimex_ESP32_EVB_REV_B_eth_example: ETHPMASK:0.0.0.0
I (6577) Olimex_ESP32_EVB_REV_B_eth_example: ETHPGW:0.0.0.0
I (6587) Olimex_ESP32_EVB_REV_B_eth_example: ~~~~~~~~~~~
.
.
. so on



my config for ETH_PHY_demo:


#
# Automatically generated file; DO NOT EDIT.
# Espressif IoT Development Framework Configuration
#

#
# SDK tool configuration
#
CONFIG_TOOLPREFIX="xtensa-esp32-elf-"
CONFIG_PYTHON="python"
CONFIG_MAKE_WARN_UNDEFINED_VARIABLES=y

#
# Bootloader config
#
CONFIG_LOG_BOOTLOADER_LEVEL_NONE=
CONFIG_LOG_BOOTLOADER_LEVEL_ERROR=
CONFIG_LOG_BOOTLOADER_LEVEL_WARN=
CONFIG_LOG_BOOTLOADER_LEVEL_INFO=y
CONFIG_LOG_BOOTLOADER_LEVEL_DEBUG=
CONFIG_LOG_BOOTLOADER_LEVEL_VERBOSE=
CONFIG_LOG_BOOTLOADER_LEVEL=3
CONFIG_BOOTLOADER_VDDSDIO_BOOST_1_8V=
CONFIG_BOOTLOADER_VDDSDIO_BOOST_1_9V=y
CONFIG_BOOTLOADER_FACTORY_RESET=
CONFIG_BOOTLOADER_APP_TEST=

#
# Security features
#
CONFIG_SECURE_BOOT_ENABLED=
CONFIG_FLASH_ENCRYPTION_ENABLED=

#
# Serial flasher config
#
CONFIG_ESPTOOLPY_PORT="COM7"
CONFIG_ESPTOOLPY_BAUD_115200B=y
CONFIG_ESPTOOLPY_BAUD_230400B=
CONFIG_ESPTOOLPY_BAUD_921600B=
CONFIG_ESPTOOLPY_BAUD_2MB=
CONFIG_ESPTOOLPY_BAUD_OTHER=
CONFIG_ESPTOOLPY_BAUD_OTHER_VAL=115200
CONFIG_ESPTOOLPY_BAUD=115200
CONFIG_ESPTOOLPY_COMPRESSED=
CONFIG_FLASHMODE_QIO=
CONFIG_FLASHMODE_QOUT=
CONFIG_FLASHMODE_DIO=y
CONFIG_FLASHMODE_DOUT=
CONFIG_ESPTOOLPY_FLASHMODE="dio"
CONFIG_ESPTOOLPY_FLASHFREQ_80M=
CONFIG_ESPTOOLPY_FLASHFREQ_40M=y
CONFIG_ESPTOOLPY_FLASHFREQ_26M=
CONFIG_ESPTOOLPY_FLASHFREQ_20M=
CONFIG_ESPTOOLPY_FLASHFREQ="40m"
CONFIG_ESPTOOLPY_FLASHSIZE_1MB=
CONFIG_ESPTOOLPY_FLASHSIZE_2MB=
CONFIG_ESPTOOLPY_FLASHSIZE_4MB=y
CONFIG_ESPTOOLPY_FLASHSIZE_8MB=
CONFIG_ESPTOOLPY_FLASHSIZE_16MB=
CONFIG_ESPTOOLPY_FLASHSIZE="4MB"
CONFIG_ESPTOOLPY_FLASHSIZE_DETECT=y
CONFIG_ESPTOOLPY_BEFORE_RESET=y
CONFIG_ESPTOOLPY_BEFORE_NORESET=
CONFIG_ESPTOOLPY_BEFORE="default_reset"
CONFIG_ESPTOOLPY_AFTER_RESET=y
CONFIG_ESPTOOLPY_AFTER_NORESET=
CONFIG_ESPTOOLPY_AFTER="hard_reset"
CONFIG_MONITOR_BAUD_9600B=
CONFIG_MONITOR_BAUD_57600B=
CONFIG_MONITOR_BAUD_115200B=y
CONFIG_MONITOR_BAUD_230400B=
CONFIG_MONITOR_BAUD_921600B=
CONFIG_MONITOR_BAUD_2MB=
CONFIG_MONITOR_BAUD_OTHER=
CONFIG_MONITOR_BAUD_OTHER_VAL=115200
CONFIG_MONITOR_BAUD=115200

#
# Example Configuration
#
CONFIG_PHY_LAN8720=y
CONFIG_PHY_ADDRESS=0
CONFIG_PHY_USE_POWER_PIN=
CONFIG_PHY_SMI_MDC_PIN=23
CONFIG_PHY_SMI_MDIO_PIN=18

#
# Partition Table
#
CONFIG_PARTITION_TABLE_SINGLE_APP=y
CONFIG_PARTITION_TABLE_TWO_OTA=
CONFIG_PARTITION_TABLE_CUSTOM=
CONFIG_PARTITION_TABLE_CUSTOM_FILENAME="partitions.csv"
CONFIG_PARTITION_TABLE_CUSTOM_APP_BIN_OFFSET=0x10000
CONFIG_PARTITION_TABLE_FILENAME="partitions_singleapp.csv"
CONFIG_APP_OFFSET=0x10000
CONFIG_PARTITION_TABLE_MD5=y

#
# Compiler options
#
CONFIG_OPTIMIZATION_LEVEL_DEBUG=y
CONFIG_OPTIMIZATION_LEVEL_RELEASE=
CONFIG_OPTIMIZATION_ASSERTIONS_ENABLED=y
CONFIG_OPTIMIZATION_ASSERTIONS_SILENT=
CONFIG_OPTIMIZATION_ASSERTIONS_DISABLED=
CONFIG_CXX_EXCEPTIONS=
CONFIG_STACK_CHECK_NONE=y
CONFIG_STACK_CHECK_NORM=
CONFIG_STACK_CHECK_STRONG=
CONFIG_STACK_CHECK_ALL=
CONFIG_STACK_CHECK=
CONFIG_WARN_WRITE_STRINGS=

#
# Component config
#

#
# Application Level Tracing
#
CONFIG_ESP32_APPTRACE_DEST_TRAX=
CONFIG_ESP32_APPTRACE_DEST_NONE=y
CONFIG_ESP32_APPTRACE_ENABLE=
CONFIG_ESP32_APPTRACE_LOCK_ENABLE=y
CONFIG_AWS_IOT_SDK=

#
# Bluetooth
#
CONFIG_BT_ENABLED=
CONFIG_BTDM_CONTROLLER_PINNED_TO_CORE=0
CONFIG_BT_RESERVE_DRAM=0

#
# ADC configuration
#
CONFIG_ADC_FORCE_XPD_FSM=
CONFIG_ADC2_DISABLE_DAC=y

#
# ESP32-specific
#
CONFIG_ESP32_DEFAULT_CPU_FREQ_80=
CONFIG_ESP32_DEFAULT_CPU_FREQ_160=y
CONFIG_ESP32_DEFAULT_CPU_FREQ_240=
CONFIG_ESP32_DEFAULT_CPU_FREQ_MHZ=160
CONFIG_SPIRAM_SUPPORT=
CONFIG_MEMMAP_TRACEMEM=
CONFIG_MEMMAP_TRACEMEM_TWOBANKS=
CONFIG_ESP32_TRAX=
CONFIG_TRACEMEM_RESERVE_DRAM=0x0
CONFIG_ESP32_ENABLE_COREDUMP_TO_FLASH=
CONFIG_ESP32_ENABLE_COREDUMP_TO_UART=
CONFIG_ESP32_ENABLE_COREDUMP_TO_NONE=y
CONFIG_ESP32_ENABLE_COREDUMP=
CONFIG_TWO_UNIVERSAL_MAC_ADDRESS=
CONFIG_FOUR_UNIVERSAL_MAC_ADDRESS=y
CONFIG_NUMBER_OF_UNIVERSAL_MAC_ADDRESS=4
CONFIG_SYSTEM_EVENT_QUEUE_SIZE=32
CONFIG_SYSTEM_EVENT_TASK_STACK_SIZE=4096
CONFIG_MAIN_TASK_STACK_SIZE=4096
CONFIG_IPC_TASK_STACK_SIZE=1024
CONFIG_TIMER_TASK_STACK_SIZE=3584
CONFIG_NEWLIB_STDOUT_LINE_ENDING_CRLF=y
CONFIG_NEWLIB_STDOUT_LINE_ENDING_LF=
CONFIG_NEWLIB_STDOUT_LINE_ENDING_CR=
CONFIG_NEWLIB_STDIN_LINE_ENDING_CRLF=
CONFIG_NEWLIB_STDIN_LINE_ENDING_LF=
CONFIG_NEWLIB_STDIN_LINE_ENDING_CR=y
CONFIG_NEWLIB_NANO_FORMAT=
CONFIG_CONSOLE_UART_DEFAULT=y
CONFIG_CONSOLE_UART_CUSTOM=
CONFIG_CONSOLE_UART_NONE=
CONFIG_CONSOLE_UART_NUM=0
CONFIG_CONSOLE_UART_BAUDRATE=115200
CONFIG_ULP_COPROC_ENABLED=
CONFIG_ULP_COPROC_RESERVE_MEM=0
CONFIG_ESP32_PANIC_PRINT_HALT=
CONFIG_ESP32_PANIC_PRINT_REBOOT=y
CONFIG_ESP32_PANIC_SILENT_REBOOT=
CONFIG_ESP32_PANIC_GDBSTUB=
CONFIG_ESP32_DEBUG_OCDAWARE=y
CONFIG_ESP32_DEBUG_STUBS_ENABLE=y
CONFIG_INT_WDT=y
CONFIG_INT_WDT_TIMEOUT_MS=300
CONFIG_INT_WDT_CHECK_CPU1=y
CONFIG_TASK_WDT=y
CONFIG_TASK_WDT_PANIC=
CONFIG_TASK_WDT_TIMEOUT_S=5
CONFIG_TASK_WDT_CHECK_IDLE_TASK_CPU0=y
CONFIG_TASK_WDT_CHECK_IDLE_TASK_CPU1=y
CONFIG_BROWNOUT_DET=y
CONFIG_BROWNOUT_DET_LVL_SEL_0=y
CONFIG_BROWNOUT_DET_LVL_SEL_1=
CONFIG_BROWNOUT_DET_LVL_SEL_2=
CONFIG_BROWNOUT_DET_LVL_SEL_3=
CONFIG_BROWNOUT_DET_LVL_SEL_4=
CONFIG_BROWNOUT_DET_LVL_SEL_5=
CONFIG_BROWNOUT_DET_LVL_SEL_6=
CONFIG_BROWNOUT_DET_LVL_SEL_7=
CONFIG_BROWNOUT_DET_LVL=0
CONFIG_ESP32_TIME_SYSCALL_USE_RTC_FRC1=y
CONFIG_ESP32_TIME_SYSCALL_USE_RTC=
CONFIG_ESP32_TIME_SYSCALL_USE_FRC1=
CONFIG_ESP32_TIME_SYSCALL_USE_NONE=
CONFIG_ESP32_RTC_CLOCK_SOURCE_INTERNAL_RC=y
CONFIG_ESP32_RTC_CLOCK_SOURCE_EXTERNAL_CRYSTAL=
CONFIG_ESP32_RTC_CLK_CAL_CYCLES=1024
CONFIG_ESP32_DEEP_SLEEP_WAKEUP_DELAY=2000
CONFIG_ESP32_XTAL_FREQ_40=
CONFIG_ESP32_XTAL_FREQ_26=
CONFIG_ESP32_XTAL_FREQ_AUTO=y
CONFIG_ESP32_XTAL_FREQ=0
CONFIG_DISABLE_BASIC_ROM_CONSOLE=
CONFIG_NO_BLOBS=
CONFIG_ESP_TIMER_PROFILING=
CONFIG_COMPATIBLE_PRE_V2_1_BOOTLOADERS=
CONFIG_ESP_ERR_TO_NAME_LOOKUP=y

#
# Wi-Fi
#
CONFIG_ESP32_WIFI_STATIC_RX_BUFFER_NUM=10
CONFIG_ESP32_WIFI_DYNAMIC_RX_BUFFER_NUM=32
CONFIG_ESP32_WIFI_STATIC_TX_BUFFER=
CONFIG_ESP32_WIFI_DYNAMIC_TX_BUFFER=y
CONFIG_ESP32_WIFI_TX_BUFFER_TYPE=1
CONFIG_ESP32_WIFI_DYNAMIC_TX_BUFFER_NUM=32
CONFIG_ESP32_WIFI_CSI_ENABLED=
CONFIG_ESP32_WIFI_AMPDU_TX_ENABLED=y
CONFIG_ESP32_WIFI_TX_BA_WIN=6
CONFIG_ESP32_WIFI_AMPDU_RX_ENABLED=y
CONFIG_ESP32_WIFI_RX_BA_WIN=6
CONFIG_ESP32_WIFI_NVS_ENABLED=y
CONFIG_ESP32_WIFI_TASK_PINNED_TO_CORE_0=y
CONFIG_ESP32_WIFI_TASK_PINNED_TO_CORE_1=

#
# PHY
#
CONFIG_ESP32_PHY_CALIBRATION_AND_DATA_STORAGE=y
CONFIG_ESP32_PHY_INIT_DATA_IN_PARTITION=
CONFIG_ESP32_PHY_MAX_WIFI_TX_POWER=20
CONFIG_ESP32_PHY_MAX_TX_POWER=20

#
# Power Management
#
CONFIG_PM_ENABLE=

#
# ADC-Calibration
#
CONFIG_ADC_CAL_EFUSE_TP_ENABLE=y
CONFIG_ADC_CAL_EFUSE_VREF_ENABLE=y
CONFIG_ADC_CAL_LUT_ENABLE=y

#
# ESP HTTP client
#
CONFIG_ESP_HTTP_CLIENT_ENABLE_HTTPS=y

#
# Ethernet
#
CONFIG_DMA_RX_BUF_NUM=10
CONFIG_DMA_TX_BUF_NUM=10
CONFIG_EMAC_L2_TO_L3_RX_BUF_MODE=
CONFIG_EMAC_TASK_PRIORITY=20

#
# FAT Filesystem support
#
CONFIG_FATFS_CODEPAGE_DYNAMIC=
CONFIG_FATFS_CODEPAGE_437=y
CONFIG_FATFS_CODEPAGE_720=
CONFIG_FATFS_CODEPAGE_737=
CONFIG_FATFS_CODEPAGE_771=
CONFIG_FATFS_CODEPAGE_775=
CONFIG_FATFS_CODEPAGE_850=
CONFIG_FATFS_CODEPAGE_852=
CONFIG_FATFS_CODEPAGE_855=
CONFIG_FATFS_CODEPAGE_857=
CONFIG_FATFS_CODEPAGE_860=
CONFIG_FATFS_CODEPAGE_861=
CONFIG_FATFS_CODEPAGE_862=
CONFIG_FATFS_CODEPAGE_863=
CONFIG_FATFS_CODEPAGE_864=
CONFIG_FATFS_CODEPAGE_865=
CONFIG_FATFS_CODEPAGE_866=
CONFIG_FATFS_CODEPAGE_869=
CONFIG_FATFS_CODEPAGE_932=
CONFIG_FATFS_CODEPAGE_936=
CONFIG_FATFS_CODEPAGE_949=
CONFIG_FATFS_CODEPAGE_950=
CONFIG_FATFS_CODEPAGE=437
CONFIG_FATFS_LFN_NONE=y
CONFIG_FATFS_LFN_HEAP=
CONFIG_FATFS_LFN_STACK=
CONFIG_FATFS_FS_LOCK=0
CONFIG_FATFS_TIMEOUT_MS=10000
CONFIG_FATFS_PER_FILE_CACHE=y

#
# FreeRTOS
#
CONFIG_FREERTOS_UNICORE=
CONFIG_FREERTOS_CORETIMER_0=y
CONFIG_FREERTOS_CORETIMER_1=
CONFIG_FREERTOS_HZ=100
CONFIG_FREERTOS_ASSERT_ON_UNTESTED_FUNCTION=y
CONFIG_FREERTOS_CHECK_STACKOVERFLOW_NONE=
CONFIG_FREERTOS_CHECK_STACKOVERFLOW_PTRVAL=
CONFIG_FREERTOS_CHECK_STACKOVERFLOW_CANARY=y
CONFIG_FREERTOS_WATCHPOINT_END_OF_STACK=
CONFIG_FREERTOS_INTERRUPT_BACKTRACE=y
CONFIG_FREERTOS_THREAD_LOCAL_STORAGE_POINTERS=1
CONFIG_FREERTOS_ASSERT_FAIL_ABORT=y
CONFIG_FREERTOS_ASSERT_FAIL_PRINT_CONTINUE=
CONFIG_FREERTOS_ASSERT_DISABLE=
CONFIG_FREERTOS_IDLE_TASK_STACKSIZE=1024
CONFIG_FREERTOS_ISR_STACKSIZE=1536
CONFIG_FREERTOS_LEGACY_HOOKS=
CONFIG_FREERTOS_MAX_TASK_NAME_LEN=16
CONFIG_SUPPORT_STATIC_ALLOCATION=
CONFIG_TIMER_TASK_PRIORITY=1
CONFIG_TIMER_TASK_STACK_DEPTH=2048
CONFIG_TIMER_QUEUE_LENGTH=10
CONFIG_FREERTOS_QUEUE_REGISTRY_SIZE=0
CONFIG_FREERTOS_USE_TRACE_FACILITY=
CONFIG_FREERTOS_GENERATE_RUN_TIME_STATS=
CONFIG_FREERTOS_DEBUG_INTERNALS=

#
# Heap memory debugging
#
CONFIG_HEAP_POISONING_DISABLED=y
CONFIG_HEAP_POISONING_LIGHT=
CONFIG_HEAP_POISONING_COMPREHENSIVE=
CONFIG_HEAP_TRACING=

#
# libsodium
#

#
# Log output
#
CONFIG_LOG_DEFAULT_LEVEL_NONE=
CONFIG_LOG_DEFAULT_LEVEL_ERROR=
CONFIG_LOG_DEFAULT_LEVEL_WARN=
CONFIG_LOG_DEFAULT_LEVEL_INFO=y
CONFIG_LOG_DEFAULT_LEVEL_DEBUG=
CONFIG_LOG_DEFAULT_LEVEL_VERBOSE=
CONFIG_LOG_DEFAULT_LEVEL=3
CONFIG_LOG_COLORS=y

#
# LWIP
#
CONFIG_L2_TO_L3_COPY=
CONFIG_LWIP_IRAM_OPTIMIZATION=
CONFIG_LWIP_MAX_SOCKETS=10
CONFIG_USE_ONLY_LWIP_SELECT=
CONFIG_LWIP_SO_REUSE=
CONFIG_LWIP_SO_RCVBUF=
CONFIG_LWIP_DHCP_MAX_NTP_SERVERS=1
CONFIG_LWIP_IP_FRAG=
CONFIG_LWIP_IP_REASSEMBLY=
CONFIG_LWIP_STATS=
CONFIG_LWIP_ETHARP_TRUST_IP_MAC=y
CONFIG_TCPIP_RECVMBOX_SIZE=32
CONFIG_LWIP_DHCP_DOES_ARP_CHECK=y

#
# DHCP server
#
CONFIG_LWIP_DHCPS_LEASE_UNIT=60
CONFIG_LWIP_DHCPS_MAX_STATION_NUM=8
CONFIG_LWIP_AUTOIP=
CONFIG_LWIP_NETIF_LOOPBACK=y
CONFIG_LWIP_LOOPBACK_MAX_PBUFS=8

#
# TCP
#
CONFIG_LWIP_MAX_ACTIVE_TCP=16
CONFIG_LWIP_MAX_LISTENING_TCP=16
CONFIG_TCP_MAXRTX=12
CONFIG_TCP_SYNMAXRTX=6
CONFIG_TCP_MSS=1436
CONFIG_TCP_MSL=60000
CONFIG_TCP_SND_BUF_DEFAULT=5744
CONFIG_TCP_WND_DEFAULT=5744
CONFIG_TCP_RECVMBOX_SIZE=6
CONFIG_TCP_QUEUE_OOSEQ=y
CONFIG_ESP_TCP_KEEP_CONNECTION_WHEN_IP_CHANGES=
CONFIG_TCP_OVERSIZE_MSS=y
CONFIG_TCP_OVERSIZE_QUARTER_MSS=
CONFIG_TCP_OVERSIZE_DISABLE=

#
# UDP
#
CONFIG_LWIP_MAX_UDP_PCBS=16
CONFIG_UDP_RECVMBOX_SIZE=6
CONFIG_TCPIP_TASK_STACK_SIZE=2560
CONFIG_PPP_SUPPORT=

#
# ICMP
#
CONFIG_LWIP_MULTICAST_PING=
CONFIG_LWIP_BROADCAST_PING=

#
# LWIP RAW API
#
CONFIG_LWIP_MAX_RAW_PCBS=16

#
# mbedTLS
#
CONFIG_MBEDTLS_SSL_MAX_CONTENT_LEN=16384
CONFIG_MBEDTLS_DEBUG=
CONFIG_MBEDTLS_HARDWARE_AES=y
CONFIG_MBEDTLS_HARDWARE_MPI=y
CONFIG_MBEDTLS_MPI_USE_INTERRUPT=y
CONFIG_MBEDTLS_HARDWARE_SHA=y
CONFIG_MBEDTLS_HAVE_TIME=y
CONFIG_MBEDTLS_HAVE_TIME_DATE=
CONFIG_MBEDTLS_TLS_SERVER_AND_CLIENT=y
CONFIG_MBEDTLS_TLS_SERVER_ONLY=
CONFIG_MBEDTLS_TLS_CLIENT_ONLY=
CONFIG_MBEDTLS_TLS_DISABLED=
CONFIG_MBEDTLS_TLS_SERVER=y
CONFIG_MBEDTLS_TLS_CLIENT=y
CONFIG_MBEDTLS_TLS_ENABLED=y

#
# TLS Key Exchange Methods
#
CONFIG_MBEDTLS_PSK_MODES=
CONFIG_MBEDTLS_KEY_EXCHANGE_RSA=y
CONFIG_MBEDTLS_KEY_EXCHANGE_DHE_RSA=y
CONFIG_MBEDTLS_KEY_EXCHANGE_ELLIPTIC_CURVE=y
CONFIG_MBEDTLS_KEY_EXCHANGE_ECDHE_RSA=y
CONFIG_MBEDTLS_KEY_EXCHANGE_ECDHE_ECDSA=y
CONFIG_MBEDTLS_KEY_EXCHANGE_ECDH_ECDSA=y
CONFIG_MBEDTLS_KEY_EXCHANGE_ECDH_RSA=y
CONFIG_MBEDTLS_SSL_RENEGOTIATION=y
CONFIG_MBEDTLS_SSL_PROTO_SSL3=
CONFIG_MBEDTLS_SSL_PROTO_TLS1=y
CONFIG_MBEDTLS_SSL_PROTO_TLS1_1=y
CONFIG_MBEDTLS_SSL_PROTO_TLS1_2=y
CONFIG_MBEDTLS_SSL_PROTO_DTLS=
CONFIG_MBEDTLS_SSL_ALPN=y
CONFIG_MBEDTLS_SSL_SESSION_TICKETS=y

#
# Symmetric Ciphers
#
CONFIG_MBEDTLS_AES_C=y
CONFIG_MBEDTLS_CAMELLIA_C=
CONFIG_MBEDTLS_DES_C=
CONFIG_MBEDTLS_RC4_DISABLED=y
CONFIG_MBEDTLS_RC4_ENABLED_NO_DEFAULT=
CONFIG_MBEDTLS_RC4_ENABLED=
CONFIG_MBEDTLS_BLOWFISH_C=
CONFIG_MBEDTLS_XTEA_C=
CONFIG_MBEDTLS_CCM_C=y
CONFIG_MBEDTLS_GCM_C=y
CONFIG_MBEDTLS_RIPEMD160_C=

#
# Certificates
#
CONFIG_MBEDTLS_PEM_PARSE_C=y
CONFIG_MBEDTLS_PEM_WRITE_C=y
CONFIG_MBEDTLS_X509_CRL_PARSE_C=y
CONFIG_MBEDTLS_X509_CSR_PARSE_C=y
CONFIG_MBEDTLS_ECP_C=y
CONFIG_MBEDTLS_ECDH_C=y
CONFIG_MBEDTLS_ECDSA_C=y
CONFIG_MBEDTLS_ECP_DP_SECP192R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_SECP224R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_SECP256R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_SECP384R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_SECP521R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_SECP192K1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_SECP224K1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_SECP256K1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_BP256R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_BP384R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_BP512R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_CURVE25519_ENABLED=y
CONFIG_MBEDTLS_ECP_NIST_OPTIM=y

#
# OpenSSL
#
CONFIG_OPENSSL_DEBUG=
CONFIG_OPENSSL_ASSERT_DO_NOTHING=y
CONFIG_OPENSSL_ASSERT_EXIT=

#
# PThreads
#
CONFIG_ESP32_PTHREAD_TASK_PRIO_DEFAULT=5
CONFIG_ESP32_PTHREAD_TASK_STACK_SIZE_DEFAULT=3072

#
# SPI Flash driver
#
CONFIG_SPI_FLASH_VERIFY_WRITE=
CONFIG_SPI_FLASH_ENABLE_COUNTERS=
CONFIG_SPI_FLASH_ROM_DRIVER_PATCH=y
CONFIG_SPI_FLASH_WRITING_DANGEROUS_REGIONS_ABORTS=y
CONFIG_SPI_FLASH_WRITING_DANGEROUS_REGIONS_FAILS=
CONFIG_SPI_FLASH_WRITING_DANGEROUS_REGIONS_ALLOWED=

#
# SPIFFS Configuration
#
CONFIG_SPIFFS_MAX_PARTITIONS=3

#
# SPIFFS Cache Configuration
#
CONFIG_SPIFFS_CACHE=y
CONFIG_SPIFFS_CACHE_WR=y
CONFIG_SPIFFS_CACHE_STATS=
CONFIG_SPIFFS_PAGE_CHECK=y
CONFIG_SPIFFS_GC_MAX_RUNS=10
CONFIG_SPIFFS_GC_STATS=
CONFIG_SPIFFS_PAGE_SIZE=256
CONFIG_SPIFFS_OBJ_NAME_LEN=32
CONFIG_SPIFFS_USE_MAGIC=y
CONFIG_SPIFFS_USE_MAGIC_LENGTH=y
CONFIG_SPIFFS_META_LENGTH=4
CONFIG_SPIFFS_USE_MTIME=y

#
# Debug Configuration
#
CONFIG_SPIFFS_DBG=
CONFIG_SPIFFS_API_DBG=
CONFIG_SPIFFS_GC_DBG=
CONFIG_SPIFFS_CACHE_DBG=
CONFIG_SPIFFS_CHECK_DBG=
CONFIG_SPIFFS_TEST_VISUALISATION=

#
# tcpip adapter
#
CONFIG_IP_LOST_TIMER_INTERVAL=120

#
# Virtual file system
#
CONFIG_SUPPRESS_SELECT_DEBUG_OUTPUT=y

#
# Wear Levelling
#
CONFIG_WL_SECTOR_SIZE_512=
CONFIG_WL_SECTOR_SIZE_4096=y
CONFIG_WL_SECTOR_SIZE=4096



meyer

Hi,

the Problem seems to be with the DHCP Server. The Board is working when plugged direktly into a Router.
Strange that I have testet with two different DHCP Servers bevore.


LubOlimex

No boards from revision D2 had been released. The latest hardware revisions is D1.

Do not add R58 since this change is related to the other change of D2 revision (MCP2551 to MCP2562). This is not needed if your board is hardware revision D1. Furthermore these changes are not related to the Ethernet but to the CAN.
Technical support and documentation manager at Olimex

LubOlimex

Technical support and documentation manager at Olimex