Started by micign, January 16, 2013, 01:33:55 pm
dd if=/boot/sd_mmc_bootstream.raw of=/dev/mmcblk0p1
Quote from: micign on January 16, 2013, 01:33:55 pmAfter applying patch enabling rtl8192cu I modified Makefile for this piece of code to disable wifi power management
CONFIG_POWER_SAVING = y
CONFIG_POWER_SAVING = n
Quote from: micign on January 16, 2013, 02:12:58 pmHi Dragomir,As far as I know this image includes systemd and kernel config is not tight attached to the board variant (micro/maxi)Extract the tarball to the root (/) directory of your sd card. It contains 2 directories - /boot/ and /usr/lib/modules/3.7.1In usr there are modules and in boot there is kernel file itself, named sd_mmc_bootstream.raw. You should manually write this file into 1st partition of your sd card, using command like: (assuming extracted kernel is in /boot and mmcblk0 is your sd card):Code Select Expanddd if=/boot/sd_mmc_bootstream.raw of=/dev/mmcblk0p1 Unfortunately, my build doesn't contain PPP kernel modules (am I guessing right you want to use 3G USB modem?)As I wrote before, I'll post instructions how I create such bundle, so you could customize the kernel (enable PPP end desired drivers).Good luck,micign
QuoteI did it as described, but the board didn't boot. The attached serial debug console repeats just every 30 secs:0x80502008 0x8020a01d
Quote from: r3flow on February 25, 2013, 09:02:38 pmAny chance the framebuffer support with kernel 3.x in the near future?
HTLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLFCPowerPrep start initialize power...Battery Voltage = 0.59VNo battery or bad battery detected!!!.Disabling battery voltage measurements./r/nLLCFeb 23 201316:07:49EMI_CTRL 0x1C084040FRAC 0x92926192init_ddr_mt46v32m16_133Mhzpower 0x00820710Frac 0x92926192start change cpu freqhbus 0x00000003cpu 0x00010001LLLLLLLFCLJUncompressing Linux... done, booting the kernel.[ 0.000000] Booting Linux on physical CPU 0[ 0.000000] Linux version 3.7.9 (picmaster@arm-build) (gcc version 4.7.2 (GCC) ) #2 Sat Feb 23 09:58:51 EET 2013[ 0.000000] CPU: ARM926EJ-S  revision 5 (ARMv5TEJ), cr=00053177[ 0.000000] CPU: VIVT data cache, VIVT instruction cache[ 0.000000] Machine: Freescale i.MX23 (Device Tree), model: i.MX23 Olinuxino Low Cost Board[ 0.000000] Memory policy: ECC disabled, Data cache writeback[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256[ 0.000000] Kernel command line: noinitrd console=ttyAMA0,115200 root=/dev/mmcblk0p2 rw rootwait ssp1=mmc[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)[ 0.000000] Memory: 64MB = 64MB total[ 0.000000] Memory: 55248k/55248k available, 10288k reserved, 0K highmem[ 0.000000] Virtual kernel memory layout:[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)[ 0.000000] vmalloc : 0xc4800000 - 0xff000000 ( 936 MB)[ 0.000000] lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)[ 0.000000] .text : 0xc0008000 - 0xc03c9a34 (3847 kB)[ 0.000000] .init : 0xc03ca000 - 0xc03eb08c ( 133 kB)[ 0.000000] .data : 0xc03ec000 - 0xc041f010 ( 205 kB)[ 0.000000] .bss : 0xc041f034 - 0xc096cfc4 (5432 kB)...