Difference between revisions of "SAM9-L9260"

m (Generate JFFS2 image)
m (Generate UBIFS image)
Line 116: Line 116:
  
 
==== Generate UBIFS image ====
 
==== Generate UBIFS image ====
 +
 +
Before creating image some NAND parameters must be known. The shown default values are for '''K9F4G08U0F''' chip.
 +
 +
* '''PEB''' -> Physical erase block, default: 128KiB (131072)
 +
* '''LEB''' -> Logical erase block, default : 126KiB (131072)
 +
* '''min. I/O size''' -> Page size, default : 2048
 +
* '''sub-page size''' -> Subpage size, default : 512
  
 
== Projects ==
 
== Projects ==

Revision as of 05:03, 20 March 2019

Documents

Under construction

Hardware

Under construction

Software

Building at91bootstrap

Get the sources with:

   git clone -b olimex https://github.com/OLIMEX/at91bootstrap.git

Go to the cloned folder and select SAM9-L9260 configuration:

   cd at91bootstrap
   make sam9_l9260_uboot_defconfig

Compile the sources with:

   make CROSS_COMPILE=arm-linux-gnueabi-

The bootstrap file can be found at:

   binaries/sam9_l9260-dataflashcardboot--3.8.11.bin

Building kernel

Get the sources:

   git clone --depth 1 --branch linux-5.0.y git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git

Preparing rootfs

In this tutorial Debian Lenny will be used. The build process may vary, depending on host PC system. The following instructions are tested on Ubuntu 18.04.

Install required packages:

sudo apt-get update
sudo apt install -y debootstrap qemu-arm-static mtd-utils

Create empty directory, which will contain the new rootfs:

mkdir armel-lenny

Run debootstrap and wait to finish:

sudo qemu-debootstrap --arch armel lenny ./armel-lenny

Login into the new rootfs with:

sudo chroot ./armel-lenny

Set hostname and password:

echo 'sam9-l9260' > /etc/hostname
passwd

Set locales:

apt-get install locales
dpkg-reconfigure locales

Configure login console:

sed -i "s/.*T0:.*/T0:2345:respawn:\/sbin\/getty\ -L\ ttyS0\ 115200\ vt100/g" /etc/inittab

Install some additional packages:

apt-get install autoconf autotools-dev bash-completion bind9-host binutils busybox cpp ethtool ftp initramfs-tools less lsof m4 mime-support mtd-utils ntp openssh-client python telnet texinfo udev usbutils whois

Configure fstab:

cat > /etc/fstab << __EOF__
# /etc/fstab: static file system information.
#
# <file system> <mount point>   <type>  <options>       <dump>  <pass>
proc            /proc           proc    defaults        0       0
rootfs          /               jffs2   rw              0       0
__EOF__

Create missing /dev/shm folder:

sed -i '36i\\t[ ! -d /dev/shm ] && mkdir --mode=755 /dev/shm' /etc/init.d/mountdevsubfs.sh

Configure networking:

cat >> /etc/network/interfaces << __EOF__
# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp

__EOF__

Exit from chroot:

exit

Generate JFFS2 image

Run:

sudo mkfs.jffs2 -r armel-lenny/ -o lenny.jffs2 -e 128 -s 512 -p -n

Where:

  • -e 128 - 128KiB of erase block
  • -s 512 - 512B page size
  • -p - pad the output to match erase block size
  • -n - do not write cleanmarkers

Generate UBIFS image

Before creating image some NAND parameters must be known. The shown default values are for K9F4G08U0F chip.

  • PEB -> Physical erase block, default: 128KiB (131072)
  • LEB -> Logical erase block, default : 126KiB (131072)
  • min. I/O size -> Page size, default : 2048
  • sub-page size -> Subpage size, default : 512

Projects

Under construction

FAQ

Under construction