Difference between revisions of "EEG-BT"

(Created page with "This is open source project based on OpenEEG. == Concept == There are several home ECG systems, these appear to cost over $150 USD and only provide a single ECG trace which i...")
 
(Goal)
 
Line 12: Line 12:
  
 
== Goal ==
 
== Goal ==
Develop a device which can provide good quality home ECG measurement for less than 60EUR
+
Develop a device which can provide good quality home ECG measurement for less than 60EUR. The following functions would be present:
The following functions would be present
+
 
 
* 3 wire measurement
 
* 3 wire measurement
* Logging over a full day (24 hour)
+
* Logging data for a full day (24 hour)
* Lipo battery powered with enough charge to run for 24 hours
+
* Lipo battery powered with enough charge to properly operate for 24 hours
* charging over USB
+
* Able to charge via USB
* logged data transfer over USB  
+
* Able to transfer logged data transfer over USB  
* flashing LED during each pulse for user feedback
+
* Flashing LED during each pulse for user feedback
* small size to allow system to be wearable
+
* Small size that allows the system to be wearable
 
+
* Wireless connection option (bluetooth) for real time monitoring using a phone/tablet
potential functions
+
* Blood oxygenation measurement option. Potential logging to help diagnose sleep apnia issues
* wireless connection option (bluetooth) for real time monitoring using a phone / tablet
 
* blood oxygenation measurement option. Potential logging to help diagnose sleep apnia issues
 
  
 
== Links ==
 
== Links ==

Latest revision as of 05:40, 25 August 2015

This is open source project based on OpenEEG.

Concept

There are several home ECG systems, these appear to cost over $150 USD and only provide a single ECG trace which is measured between finger tips The finger tip measurement is prone to muscle action noise from the action of holding. They also are unable to monitor over a long period when the user is performing normal daily tasks.

A home ECG may show early warning signs and prompt a user to a formal check from a doctor.

Rare or occasional heart events can also be captured over the day and print outs could be taken to a doctor.

Several other open projects for ECGs were found however none found could be purchased.

Goal

Develop a device which can provide good quality home ECG measurement for less than 60EUR. The following functions would be present:

  • 3 wire measurement
  • Logging data for a full day (24 hour)
  • Lipo battery powered with enough charge to properly operate for 24 hours
  • Able to charge via USB
  • Able to transfer logged data transfer over USB
  • Flashing LED during each pulse for user feedback
  • Small size that allows the system to be wearable
  • Wireless connection option (bluetooth) for real time monitoring using a phone/tablet
  • Blood oxygenation measurement option. Potential logging to help diagnose sleep apnia issues

Links

TI app note existing olimex ECG shield is based on

ECG primer, ECG wave form and identified conditions explained in detail

wiki for ECG

Existing ECG developed under an Open license

ECG experiments

non contact ECG

ECG with ads1298

eHealth

MobilECG Open Source 12 leads design

Documents

Under construction

Hardware

Under construction

Software

Under construction

Projects

Under construction

FAQ

Under construction

Current Actions and Progress

Learnings

  • Tested the existing shield-EKG-EMG - Found gain works well however noise from power systems presented on the output even when battery powered and with the 40hz and above filter. This means a design based on the existing system would rely on software to isolate and remove 50,60hz noise
  • test of shielded probes to reduce 50,60hz interference - Using shielded wire on all probes with the shield connected to the ref voltage found noise was removed when connecting the left and right arm probe together. However when connecting to the body the overall noise pick up on the body negated the affect.

Current Actions

  • A prototype board has been designed and is being manufactured. The board intends to test
    • 3 measurement trace circuit compared to existing 1 measurement trace
    • isolation methods. Noise reduction strategy and isolation for protection will be tested
    • A concept to reduce 50,60hz noise using right leg drive method which injects a signal to counteract noise
    • A different type of instrumentation amp on the front end of the analogue section to see if it reduces noise
    • Power test to check for likely battery needs
    • Check performance of a less complex and smaller reference voltage circuit
  • Investigating methods to reduce mains frequency interference (50,60hz). Testing has shown and several reports of noise present in shield-EKG-EMG
  • Alternative probe options, IE option to use probes to stick to skin