A13-SOM

Revision as of 00:26, 16 October 2014 by LubOlimex (talk | contribs) (Android)

A13-SOM-1.jpeg A13-SOM-2.jpeg


A13-SOM-XXX features:

  • A13 Cortex-A8 CPU and Mali 400 GPU
  • 256 or 512MB DDR3 RAM memory
  • Power supply managment
  • 1x LCD connector
  • 3x GPIO connectors
  • MicroSD card connector
  • DEBUG-UART connector for console debug with USB-SERIAL-CABLE-F
  • status LED
  • Power LED
  • RESET button
  • 3.3V input power supply
  • PCB dimensions: 61 x 33 mm

Official Images from OLIMEX

Linux

Torrent of Debian release 1: A13-SOM-256 Debian Linux with kernel 3.4.90+

Direct download location of Debian release 1: A13-SOM-256 Debian 4GB SD-card image release-1 with hardware accelerated video and more

Torrent of Debian release 1: A13-SOM-512 Debian Linux with kernel 3.4.90+

Direct download location of debian release 1: A13-SOM-512 Debian 4GB SD-card image release-1 with hardware accelerated video and more

The image features:

  • Linux Kernel 3.4.90+
  • XFCE4 desktop environment
  • Mplayer CLI
  • GCC 4.6
  • 4.3"(480x272), 7"(800x480), 10" (1024x600) and 15.6" (1366x768) LCD and touchscreen support
  • GPIO
  • I2C
  • USB WIFI RTL8188CU, Ethernet AX88772B
  • dpkg
  • git
  • i2c-tools
  • perl
  • xorg
  • Python 2.7
  • USB-ETHERNET-AX88772B
  • MOD-WIFI-RTL8188
  • A13-LCD 4.3″TS 4.3″ LCD with backlight and touchscreen 480×272 pixels
  • A13-LCD7″TS 7″ LCD with backlight and touchscreen 800×480 pixels
  • A10-LCD10″TS 10.1″ LCD with backlight and touchscreen 1024×600 pixels
  • Micro SD card
  • OTG USB
  • HIGH SPEED HOST1 USB
  • I2C2(100KHz)
  • I2C1(100KHz)
  • Default Login: root/olimex


Tested board peripherals with this image:

  • GPIO - located at /sys/class/gpio
  • LCD - supported are A13-LCD4.3TS, A13-LCD7TS, A13-LCD10TS
  • Touch screen - you need calibrate LCD before using touch screen. Type: ts_calibrate and then test it with ts_test
  • ASIX 8877 USB-LAN - USB-ETHERNET-AX88772B
  • RTL8188CU - MOD-WIFI-RTL8188
  • USB_OTG - works as OTG device and Low/Full/High USB host
  • USB_HOST - works as Low/Full/High USB host
  • mico_SD_card - allow Linux boot
  • I2C2(100KHz) - /dev/i2c-2
  • I2C1(100KHz) - /dev/i2c-1


Note: the A13-SOM-Debian-SD card which we have in our web store contains the same image on 4GB Class10 fast micro SDcard, if you want to use this image please use card of Class10 speed or the performance of Linux will be very slow.

Note: in the previous Debian releases the Ethernet was auto-detected and initialized during boot BUT this was causing big delays in the start-up of the board if you didn't want to use Ethernet or if there wasn't Ethernet cable connected.

You can enable it by following these two steps:

1. To check under what name the LAN is associated write "ifconfig –a"

2. If, for example, it is under eth0 name, then write: "dhclient eth0"

This should enable the Ethernet and then SSH would also be available.

Android

Note that the Android is suitable only for the A13-SOM-512 version of the board (the 256 version of the board is not equipped with enough RAM to run Android smoothly). To upload the Android to the NAND you would also need A13-SOM-WIFI-4GB (to extend the board with NAND flash memory).

Torrent of Android 4.2.2 release 1 for NAND memory: A13-SOM-512 Android for NAND

Direct download of Android 4.2.2 release 1 NAND memory: A13-SOM-512 Android for NAND

The image is with these features:

  • Android 4.2.2
  • NAND image i.e. will work only on [A13-SOM-512+A13-SOM-WIFI-4GB]
  • Supports 7" LCD 800x480 pixels
  • Touchscreen supported
  • GPIO support
  • USB-Ethernet ASIX 88772
  • USB-WIFI RTL8188
  • USB-OTG support USB device and USB host with Low/Full/High speed
  • USB-HOST-top Low/Full/High speed
  • micro SD card
  • I2C1
  • I2C2
  • Buttons


Documents

A13 Datasheet

A13 datasheet


A13 User Manual

A13 Users manual

Hardware


Power supply and consumption

A13-SOM can be powered from:

  • +3.3V voltage applied to GPIO-1

Power consumption is as follows:

Board dimensions

A13-SOM-XXX basic dimensions might be seen in the picture here: A13-SOM board dimensions

Schematic

A13-SOM-256/512 schemaitc is available at GitHub

A13-SOM-WIFI schematic and CAD files are at GitHub

The CAD product used to design A13-SOM-WIFI is Eagle and you can download evaluation free version from their web.


Board Layout

A13-SOM-512.png

Software

Linux Commands

Linux-Commands Brief Linux Command reference


Python

GPIO under Linux

How To?

How to generate boot-able SD-card Debian Linux image for A13-SOM?

The building instructions might be found in this document: Google drive mirror

Official Wordpress post on Debian image release: Wordpress post

How to download new Android image to the NAND memory of my A13-SOM board?

How do I write the official Android image to a micro SD card for my A13-SOM board?

How do I write the Linux image to a micro SD card to use with my A13-SOM board?

How to change LCD resolutions?

How to detect and enable the Ethernet controller (if it is disabled by default)?

How to install Android on SD-card?

How to access UART, I2C, GPIOs under Android?

How to control PWM under Linux?

How to properly calibrate a display under Debian

How to add STK1160 video capture driver support in Kernel 3.4

STK1160 driver backport by Dimitar Tomov


Main_Page