MOD-RFID1356MIFARE - Revision history

LubOlimex: /* Bootloader mode (firmware upgrade) */

2025-01-23T12:03:15Z

‎Bootloader mode (firmware upgrade)

LubOlimex: /* Operation */

2023-01-20T07:54:13Z

‎Operation

LubOlimex: /* Operation */

2023-01-20T07:53:53Z

‎Operation

LubOlimex: /* ERROR SET FOR CDC AND UART MODE */

2021-11-22T13:35:18Z

‎ERROR SET FOR CDC AND UART MODE

LubOlimex: /* Description */

2020-12-22T06:58:42Z

‎Description

LubOlimex: /* USB-CDC mode */

2020-02-26T14:45:49Z

‎USB-CDC mode

LubOlimex: /* USB-CDC mode */

2020-02-26T14:32:12Z

‎USB-CDC mode

LubOlimex: /* COMMAND SET FOR CDC AND UART MODE */

2020-02-26T14:30:23Z

‎COMMAND SET FOR CDC AND UART MODE

LubOlimex: /* COMMAND SET FOR CDC AND UART MODE */

2020-02-26T14:28:16Z

‎COMMAND SET FOR CDC AND UART MODE

LubOlimex: /* COMMAND SET FOR CDC AND UART MODE */

2020-02-26T14:10:06Z

‎COMMAND SET FOR CDC AND UART MODE

@@ Line 55: / Line 55: @@
 To update the firmware we need a couple of software resources:
-.1. First install serial terminal software that is capable of sending files via the serial connection. We used the open source TeraTerm software here, and this is the terminal software that I would recommend under Windows. The web-page of TeraTerm is here: https://ttssh2.osdn.jp/index.html.en
+.1. First install serial terminal software that is capable of sending files via the serial connection. We used the open source TeraTerm software here, and this is the terminal software that I would recommend under Windows. The web-page of TeraTerm is here: https://teratermproject.github.io/index-en.html
 Linux guys should use software terminal that supports XMODEM transfer.

@@ Line 12: / Line 12: @@
 The board can operate in the following user modes:
-* USB-HID - acts as keyboard with QWERTY layout, prints the ID of the read tags in a text field
+* USB-HID - acts as QWERTY keyboard, prints the ID of the read tags in a text field
 * UART - allows connection to equipment via the serial cable at the UEXT, allows usage of different commands at fixed baud rate of 38400
 * USB-CDC - same as above but via the mini USB port and can work up to 115200

@@ Line 12: / Line 12: @@
 The board can operate in the following user modes:
-* USB-HID - acts as human interface device, prints the ID of the read tags in a text field
+* USB-HID - acts as keyboard with QWERTY layout, prints the ID of the read tags in a text field
 * UART - allows connection to equipment via the serial cable at the UEXT, allows usage of different commands at fixed baud rate of 38400
 * USB-CDC - same as above but via the mini USB port and can work up to 115200

@@ Line 329: / Line 329: @@
 x13	DEP Protocol / Mifare / ISO/IEC 14443-4: The data format does not match to the
    specification.
-x14	Mifare: Authentication error (improper Key used
+x14	Mifare: Authentication error (improper Key used); make sure EEPROM is present and readable
 x23	ISO/IEC 14443-3: UID Check byte is wrong
 x7f	unknown command

@@ Line 4: / Line 4: @@
 MOD-RFID1356MIFARE is an Olimex device that allows you to read and write NFC / MIFARE RFID tags operating at 13.56Mhz.
 MOD-RFID1356MIFARE uses NXP PN532 to read and write NFC / MIFARE RFID cards. In addition we put second microcontroller on the board which allow 3 additional ways to communicate with host device: USB HID keyboard, USB CDC serial communication, and UART CMOS level for boards with UEXT.
 == Operation ==

← Older revision		Revision as of 14:45, 26 February 2020
Line 286:		Line 286:

	* '''mku''' - Unlocks read command and resets keys to ka=000000000000 and kb=FFFFFFFFFFFF		* '''mku''' - Unlocks read command and resets keys to ka=000000000000 and kb=FFFFFFFFFFFF
		+	>mku
		+	OK
		+	>ka
		+	Key A : 000000000000
		+	OK
		+	>kb
		+	Key B : FFFFFFFFFFFF
		+	OK
		+	>

	==== ERROR SET FOR CDC AND UART MODE ====		==== ERROR SET FOR CDC AND UART MODE ====

@@ Line 267: / Line 267: @@
    >ka
    ERR:0x7f
    >er6 7
    OK
--AA0E012C-
+  >-AA0E012C-
-Block   6 : 12 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
+  Block   6 : 12 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
-Block   7 : 00 00 00 00 00 00 FF 07 80 69 FF FF FF FF FF FF
+  Block   7 : 00 00 00 00 00 00 FF 07 80 69 FF FF FF FF FF FF
-OK
+  OK
 * '''muA''' - set UID of target card for next write operation (A=UID)
 * '''mku''' - Unlocks read command and resets keys to ka=000000000000 and kb=FFFFFFFFFFFF

@@ Line 261: / Line 261: @@
    >mkl
    ok
+   >ka 112233445566
 * '''muA''' - set UID of target card for next write operation (A=UID)

@@ Line 257: / Line 257: @@
    OK
+   >
 ==== ERROR SET FOR CDC AND UART MODE ====

@@ Line 154: / Line 154: @@
 Note that there is no command line help in the latest firmware (no space available for help); however we introduced error messages, that can be seen! The switch to bootloader mode command was also removed. The commands available are described below follows:
-  i - shows information about the firmware
+  i - shows information about the firmware;
-  erB - Read data in block B.
+  erB - Read data in block B;
-  erS,E - Read data from block S to block E.
+  erS,E - Read data from block S to block E;
-  ewB,X - Write data to block B. X must be hex, maximum 16 bytes.
+  ewB,X - Write data to block B. X must be hex, maximum 16 bytes. If mkl enabled - should be preceded by muA;
-  e0 - Disable eeprom read.
+  e0 - Disable eeprom read;
-  e1 - Enable eeprom read.
+  e1 - Enable eeprom read;
-  mlE - Set led mode to disabled (E=0) or enabled (E=1)
+  mlE - Set led mode to disabled (E=0) or enabled (E=1);
-  mtF - Set scan interval. Values between 1 and 30000 are accepted.
+  mtF - Set scan interval. Values between 1 and 30000 are accepted;
-  mkK - Set work key, (K=a) for Key_A or (K=b) for Key_B.
+  mkK - Set work key, (K=a) for Key_A or (K=b) for Key_B;
-  kA - Read current key, where A is 'a', 'b' or '?'.
+  kA - Read current key, where A is 'a', 'b' or '?'. Will not work if locked with mkl;
   kA,X - Set new key, where A is 'a' or 'b'. X is 6 bytes in hex format.
@@ Line 248: / Line 251: @@
   OK
-* '''k?''' - Shows the currently selected key and the value stored
+* '''k?''' - Shows the currently selected key and the value stored, unless locked with mkl
    >k?