Once it worked well for programming ATiny series in BASCOM.
Trying to program in C i changed the firmware ( in windows 10.64) (page 16 olimex avr-isp-mk2 manual),with microchip studio 7. For using again the Bascom-avr IDE, i uninstalled microchip studio 7and the driver.
But now in Bascom-avr-ide it funtion no longer, not with the JUNGO driver and not with AVRDUDE.
Does anyone have a solution ?
Thanks
You wrote that you changed the firmware to work with Atmel Studio but never wrote that you revert the firmware back. Did you revert the firmware?
Befor each driver i loaded, i puted the processor in bootloeder state (page 16 )
I tested it here under Windows 10 x64. I managed to get Bascom working by loading the latest firmware of AVR-ISP-MK2 suitable for Atmel/Microchip Studio and using the LibUSB drivers.
Maybe if the problem re-install the Microchip Studio, maybe uninstalling the studio removed the drivers?
removed all related apps. Connected programmer > reset button > disconnected programmer > connected again. Driver manager > microchip tools > AVR-ISP-MKII driver 1.2.2.0 > file version1.2.6.0 > driver files c:\windows system32\driver\libusb0 sys. In bascom-ide > options > programmer, non off the selected programmers works. ?
Check here: https://www.olimex.com/forum/index.php?topic=5939.0
According to your latest info. i treid to install the correct driver (AVRDUDE) for window 10 In BASCOM-IDE nothing happened when i wanted to upload a file. Since i don't have a atmega 16, i changed in the parameter field mega16 by t25.
Maybe the screenshots give more clarity.
Regard
Sorry i don't no how to put the images from my screenshot here
You can post images in free image sharing web-site, I usually use https://imgur.com/ and get sharable links then post links to them here.
hhttps://imgur.com/81GCpmZttps://imgur.com/ATHbJ0U
Hopefully this worked
regards
It doesn't show all the info needed. You should've showed the properties of the debugger in device manager to see exact driver associated with it.
Look how it looks here in the three pictures, compare with your side:
https://imgur.com/a/PGVUkNV
maybe i erased the screenshots on the imgursite, can you send them again ( my apologies ).
I reinstalled libusb driver avr-isp-mk2 to try in bascom to use programmer > USBprog programmer / avr-isp-mkii ( gives less error codes
> maybe i erased the screenshots on the imgursite, can you send them again ( my apologies ).
You didn't erase them, just links were a bit wrong. These are your pictures that you shared in earlier post:
https://imgur.com/81GCpmZ
https://imgur.com/ATHbJ0U
These are my pictures:
https://imgur.com/a/PGVUkNV
Anyway just try to get same as my pictures! Especially the driver thing to be the same.
ican't see the images, by scrolling in a flash they disappears and can't scroll back ( black image )
this happened afther the first time i tried to enlarge the images.
Try another Internet browser...
I got the print screens. The choice of browser is irrelevant.
When open the link, immediately scrolls, otherwise the print screens disappers.
https://imgur.com/a/7MoPKFP (https://imgur.com/a/7MoPKFP)
Driver looks alright. What about he hardware connection between AVR-ISP-MK2 and the target? Which connector do you use for the connection? Target is ATtiny25 - what is the programming interface of that chip?
Did you also test with Atmel Studio just to confirm if the issue is specifically with Bascom?
The hardware is okay. But i messed with loading the hex files.
So i restarted all over again.
Fist loaded from Olimex AVR-ISP-MK2-firmware-windows drivers.zip and then extracted everything ( which i didn't not well ).
Then following the procedure from the manual: 4.2.1 changing firmware for windows users.
On point 5. file >hex files > AVRDUDE / arduino / libusb >
libusb-AVRISP-MKII.hex
At the end, everything was working fine.!!!
Thanks for always patiently replying.