Olimex Support Forum

Others => TERES DIY Laptop => Topic started by: baffo32 on August 13, 2020, 01:20:21 PM

Title: Recovering from Overvoltage
Post by: baffo32 on August 13, 2020, 01:20:21 PM
Hi,

I have an unfortunate habit of plugging my teres into 12v supplies, which immediately burns the board out.

Does anybody know which components on the board will need to be replaced after this?

Thanks so much.
Title: Re: Recovering from Overvoltage
Post by: LubOlimex on August 17, 2020, 01:54:01 PM
You can look at the top left corner at the forth page of this document - it shows the power circuit around the power jack connector: https://github.com/OLIMEX/DIY-LAPTOP/blob/rel3/HARDWARE/A64-TERES/TERES-PCB1-A64-MAIN/Rev.C/TERES_PCB1-A64-MAIN_Rev.C.pdf

First try replacing D1 SMBJ6.0A. There is good chance this diode protected further damage. If replacing it doesn't work, then the AXP803 got damaged and the chances of repair are slim.

In future consider adding a protection fuse, where the suggested FUSE2 is placed in the schematic.
Title: Re: Recovering from Overvoltage
Post by: baffo32 on September 20, 2022, 03:01:06 PM
Thank you here. I keep accidentally doing this. To add the fuse it looks like you would physically cut the wide trace the fuse almost fully spreads over, verifying afterward the two solder pads no longer conduct, and then solder an smt fuse over? The trace appears to partially spread under D1 so some delicate knife work may be needed I'm thinking.
Title: Re: Recovering from Overvoltage
Post by: LubOlimex on September 20, 2022, 03:53:30 PM
Yeah the wire is a bit thick because there is a lot of current going trough. Just cut between the two pads of FUSE2 up to D1 (and probably some under it). If it was me I'd do it starting from D1 down towards the FUSE2 pads. Some sharp cutter is needed. Also double check if the cut is properly done afterwards with a multimeter tool in short circuit detection mode. Maybe unsolder D1 temporarily or one of its ends if in the way. Once the cutting is done place the fuse.
Title: Re: Recovering from Overvoltage
Post by: kreyren on April 02, 2023, 02:42:59 AM
Referenced in https://github.com/OLIMEX/DIY-LAPTOP/issues/61 to propose adding a resettable fuse to mitigate the risk of over-voltage due to pebcak.
Title: Re: Recovering from Overvoltage
Post by: LubOlimex on April 03, 2023, 10:28:12 AM
We would consider it but if you are capable for replacing the fuse or resetting it you'd be capable to place it initially. Better to link your suggestion for fitting fuse here.
Title: Re: Recovering from Overvoltage
Post by: kreyren on April 04, 2023, 01:23:06 AM
Quote from: LubOlimex on April 03, 2023, 10:28:12 AMWe would consider it but if you are capable for replacing the fuse or resetting it you'd be capable to place it initially. Better to link your suggestion for fitting fuse here.

See my reply in https://github.com/OLIMEX/DIY-LAPTOP/issues/61#issuecomment-1495047014

Tl;dr: The fuse is e.g. https://eu.mouser.com/ProductDetail/onsemi/NIV6350MT2TXG?qs=xZ%2FP%252Ba9zWqa2xJAD3VNXxQ%3D%3D, seems to reset itself without the need of user interaction.