Hello,
I've just tried to boot the theoretically universal Armbian_5.72.1_Olinuxino-a20_Debian_stretch_next_4.19.17 image (taken from ftp://staging.olimex.com/Allwinner_Images/A20-OLinuXino/1.latest_mainline_images/stretch/images/) on my A20-SOM device, but with no success.
The following output is displayed:
**File not found /boot/dtb/ **
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command.
Aborting!
** File not found /boot/dtb/overlay/sun7i-a20-fixup.scr **
...
ERROR: Did not find a cmdline Flattened Device Tree
Could not find a valid device tree
SCRIPT FAILED: continuing...
Card did not respond to voltage select!
...
Device 0: unknown device
ethernet@01c50000 Waiting for PHY auto negotiation to complete...... TIMEOUT !
Could not initialize PHY ethernet@01c50000
I'd really appreciate any help with this, because I really need to make this work!!
Thanks in advance
Rodrigo
Probably the EEPROM doesn't contain data about the board and the universal image won't automatically recognzie your board. Interrupt u-boot with space and manually configure the image for your board. In u-boot type "olinuxino" for help and refer to chapter "Manual board configuration" of the wiki here: https://www.olimex.com/wiki/ArmbianHowTo#Manual_board_configuration
Hello,
first of all, thanks to your quick response.
Secondly, I've tried to manually configure the image for my A20-SOM board, but unsuccessfully. If I write
=> olinuxino config write 7664 d
Erasing EEPROM configuration...
ERROR: Failed to init eeprom!
Erasing MMC configuration...
Writting EEPROM configuration...
ERROR: Failed to init eeprom!
Writting MMC configuration...
=> olinuxino config info
Failed to read the EEPROM configuration!
=> saveenv
=> reset
After reboot, the system starts properly.
Thanks :-)
my guess is you have old board which has no EEPROM on it
Good, glad to help.
Your hardware revision of A20-SOM has no EEPROM at all. The EEPROM of A20-SOM was added in hardware revision E. However, this scenario was considered and it this case the board identification information gets written to the SD card instead.
Sorry to hijack a thread, but how exactly do I halt the u-boot since my keyboard isn't recognized during the boot (an older A20 Micro)?
I've tried two USB keyboards now...
To clarify:
- I'm powering the board from the power jack with 12V 2A power supply.
- The keyboards work just fine with my PC
- The keyboards work just fine with 3.4 Jessie
- Also, the Micro works just fine with the 3.4 Jessie distro
Interrupting the kernel boot and staying in u-boot is kind of a pain. You need to keep press the space key repeatedly even before seeing the countdown. If the keyboard doesn't get initialized before the prompt, you might need to use other method of accessing the board. For example, try a USB-serial converter between the board's debug port and a PC running serial terminal software then using the PC keyboard to interrupt the prompt.
Hello all
Sorry also for hijacking this thread but think is good place to claim that there is an error at this https://www.olimex.com/wiki/ArmbianHowTo armbian how to
Point 5, Manual Board Configuration
it says
Quote from: undefinedSet configuration, for example if you have A20-OLinuXino-LIME2-e16Gs16M, hardware revision K you would have to type:
olinuxino config 9604 kShould say
olinuxino config write 9604 kPlease note "WRITE"
If not by the pertinent post of @roderick, I'ld be now bald pulling my last hair
Thanks @roderick
Thanks, this is now fixed, please let me know if you spot other issues in the wiki article - I'd try to fix them ASAP.