I'm having tests with RT5350F-OLinuXino-EVB.
It worked fine with every feature. But since yesterday only WLAN doesn't work.
When power is up, WLAN_ACT blink for a second and never on later.
This is dmesg and ifconfig.
Please give me any kind of hint of help.
root@OpenWrt:/# dmesg
[ 0.000000] Linux version 3.18.19 (stefan@debian) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45456) )5
[ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
[ 0.000000] MIPS: machine is RT5350F-OLINUXINO
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 802da0d0, node_mem_map 810063c0
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=0003c4e8
[ 0.000000] Readback ErrCtl register=0003c4e8
[ 0.000000] Memory: 29016K/32768K available (2401K kernel code, 123K rwdata, 480K rodata, 188K init, 181K bss,)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 360MHz
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.010000] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.090000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110000] pinctrl core: initialized pinctrl subsystem
[ 0.120000] NET: Registered protocol family 16
[ 0.130000] rt2880-pinmux pinctrl: try to register 28 pins ...
[ 0.130000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux
[ 0.130000] pinctrl core: add 4 pinmux maps
[ 0.130000] rt2880-pinmux pinctrl: found group selector 4 for jtag
[ 0.130000] rt2880-pinmux pinctrl: invalid group "rgmii" for function "gpio"
[ 0.140000] rt2880-pinmux pinctrl: invalid group "mdio" for function "gpio"
[ 0.150000] rt2880-pinmux pinctrl: found group selector 2 for uartf
[ 0.150000] rt2880-pinmux pinctrl: request pin 17 (io17) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 18 (io18) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 19 (io19) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 20 (io20) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 21 (io21) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 7 (io7) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 8 (io8) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 9 (io9) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 10 (io10) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 11 (io11) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 12 (io12) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 13 (io13) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 14 (io14) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: failed to lookup the sleep state
[ 0.180000] rt2880_gpio 10000600.gpio: registering 22 gpios
[ 0.190000] rt2880_gpio 10000600.gpio: registering 22 irq handlers
[ 0.200000] rt2880_gpio 10000660.gpio: registering 6 gpios
[ 0.210000] rt2880_gpio 10000660.gpio: registering 6 irq handlers
[ 0.220000] Switched to clocksource systick
[ 0.230000] NET: Registered protocol family 2
[ 0.240000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.250000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.260000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.280000] TCP: reno registered
[ 0.280000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.290000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.310000] NET: Registered protocol family 1
[ 0.320000] rt-timer 10000100.timer: maximum frequency is 7324Hz
[ 0.330000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT
[ 0.330000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.360000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.370000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.390000] msgmni has been set to 56
[ 0.430000] io scheduler noop registered
[ 0.440000] io scheduler deadline registered (default)
[ 0.450000] drivers/phy/phy-ralink-usb.c:ralink_usb_phy_probe[147]
[ 0.460000] drivers/phy/phy-ralink-usb.c:ralink_usb_phy_probe[161]
[ 0.480000] rt2880-pinmux pinctrl: request pin 14 (io14) for pio:14
[ 0.480000] rt2880-pinmux pinctrl: request pin 12 (io12) for pio:12
[ 0.480000] rt2880-pinmux pinctrl: request pin 0 (io0) for pio:0
[ 0.480000] gpio-export gpio_export: 3 gpio(s) exported
[ 0.490000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.500000] serial8250 serial8250: no of_node; not parsing pinctrl DT
[ 0.500000] pinctrl core: add 1 pinmux maps
[ 0.500000] rt2880-pinmux pinctrl: found group selector 3 for uartlite
[ 0.500000] rt2880-pinmux pinctrl: request pin 15 (io15) for 10000c00.uartlite
[ 0.500000] rt2880-pinmux pinctrl: request pin 16 (io16) for 10000c00.uartlite
[ 0.500000] console [ttyS0] disabled
[ 0.510000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A
[ 0.530000] console [ttyS0] enabled
[ 0.540000] bootconsole [early0] disabled
[ 0.560000] pinctrl core: add 1 pinmux maps
[ 0.560000] pinctrl core: add 1 pinmux maps
[ 0.560000] rt2880-pinmux pinctrl: found group selector 1 for spi
[ 0.560000] rt2880-pinmux pinctrl: found group selector 6 for spi_cs1
[ 0.560000] rt2880-pinmux pinctrl: request pin 3 (io3) for 10000b00.spi
[ 0.560000] rt2880-pinmux pinctrl: request pin 4 (io4) for 10000b00.spi
[ 0.560000] rt2880-pinmux pinctrl: request pin 5 (io5) for 10000b00.spi
[ 0.560000] rt2880-pinmux pinctrl: request pin 6 (io6) for 10000b00.spi
[ 0.560000] rt2880-pinmux pinctrl: request pin 27 (io27) for 10000b00.spi
[ 0.570000] m25p80 spi32766.0: found en25q64, expected s25fl064k
[ 0.590000] m25p80 spi32766.0: en25q64 (8192 Kbytes)
[ 0.600000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.610000] Creating 4 MTD partitions on "spi32766.0":
[ 0.620000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.630000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.640000] 0x000000040000-0x000000050000 : "factory"
[ 0.650000] 0x000000050000-0x000000800000 : "firmware"
[ 0.740000] 2 uimage-fw partitions found on MTD device firmware
[ 0.760000] 0x000000050000-0x000000158ccb : "kernel"
[ 0.770000] 0x000000158ccb-0x000000800000 : "rootfs"
[ 0.780000] mtd: device 5 (rootfs) set to be root filesystem
[ 0.790000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.800000] 0x0000003d0000-0x000000800000 : "rootfs_data"
[ 0.830000] ralink_soc_eth 10100000.ethernet: generated random MAC address 12:1a:da:41:a8:1a
[ 0.840000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
[ 0.860000] rt2880_wdt 10000120.watchdog: Initialized
[ 0.870000] TCP: cubic registered
[ 0.880000] NET: Registered protocol family 17
[ 0.890000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load .
[ 0.910000] 8021q: 802.1Q VLAN Support v1.8
[ 0.950000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 0.970000] Freeing unused kernel memory: 188K (802f1000 - 80320000)
[ 3.980000] init: Console is alive
[ 3.990000] init: - watchdog -
[ 8.260000] usbcore: registered new interface driver usbfs
[ 8.270000] usbcore: registered new interface driver hub
[ 8.280000] usbcore: registered new device driver usb
[ 8.360000] SCSI subsystem initialized
[ 8.380000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.400000] ehci-platform: EHCI generic platform driver
[ 8.610000] phy phy-usbphy.0: remote usb device wakeup disabled
[ 8.620000] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 8.630000] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 8.640000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 8.660000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 8.690000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 8.700000] usb usb1: no of_node; not parsing pinctrl DT
[ 8.700000] hub 1-0:1.0: no of_node; not parsing pinctrl DT
[ 8.700000] hub 1-0:1.0: USB hub found
[ 8.710000] hub 1-0:1.0: 1 port detected
[ 8.720000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.740000] ohci-platform: OHCI generic platform driver
[ 8.750000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 8.760000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 8.780000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 8.850000] usb usb2: no of_node; not parsing pinctrl DT
[ 8.850000] hub 2-0:1.0: no of_node; not parsing pinctrl DT
[ 8.850000] hub 2-0:1.0: USB hub found
[ 8.860000] hub 2-0:1.0: 1 port detected
[ 8.880000] usbcore: registered new interface driver usb-storage
[ 9.100000] init: - preinit -
[ 10.600000] rt305x-esw 10110000.esw: link changed 0x00
[ 10.920000] random: procd urandom read with 17 bits of entropy available
[ 12.240000] rt305x-esw 10110000.esw: link changed 0x10
[ 14.370000] mount_root: loading kmods from internal overlay
[ 15.630000] jffs2: notice: (324) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (.
[ 15.670000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 15.700000] block: extroot: not configured
[ 15.950000] jffs2: notice: (321) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (.
[ 16.980000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 17.000000] block: extroot: not configured
[ 17.010000] mount_root: switching to jffs2 overlay
[ 17.080000] procd: - early -
[ 17.080000] procd: - watchdog -
[ 18.250000] procd: - ubus -
[ 19.270000] procd: - init -
[ 20.820000] NET: Registered protocol family 10
[ 20.850000] ntfs: driver 2.1.31 [Flags: R/O MODULE].
[ 20.880000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 20.920000] i2c /dev entries driver
[ 20.930000] pinctrl core: add 1 pinmux maps
[ 20.930000] rt2880-pinmux pinctrl: found group selector 0 for i2c
[ 20.930000] rt2880-pinmux pinctrl: request pin 1 (io1) for 10000900.i2c
[ 20.930000] rt2880-pinmux pinctrl: request pin 2 (io2) for 10000900.i2c
[ 20.930000] i2c-ralink 10000900.i2c: loaded
[ 20.950000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[ 20.970000] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 20.990000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 21.020000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[ 21.110000] xt_time: kernel timezone is -0000
[ 21.170000] cfg80211: Calling CRDA to update world regulatory domain
[ 21.200000] cfg80211: World regulatory domain updated:
[ 21.210000] cfg80211: DFS Master region: unset
[ 21.220000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 21.240000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 21.250000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 21.270000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 21.280000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 21.300000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 21.320000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 21.330000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 21.350000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 21.480000] PPP generic driver version 2.4.2
[ 21.490000] NET: Registered protocol family 24
[ 21.560000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
[ 21.570000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
[ 21.590000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 26.450000] rt305x-esw 10110000.esw: link changed 0x00
[ 28.100000] rt305x-esw 10110000.esw: link changed 0x10
[ 33.870000] device eth0.1 entered promiscuous mode
[ 33.880000] device eth0 entered promiscuous mode
[ 33.950000] br-lan: port 1(eth0.1) entered forwarding state
[ 33.960000] br-lan: port 1(eth0.1) entered forwarding state
[ 35.960000] br-lan: port 1(eth0.1) entered forwarding state
[ 79.920000] random: nonblocking pool is initialized
root@OpenWrt:/# ifconfig
br-lan Link encap:Ethernet HWaddr D6:27:D3:D6:DB:42
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::d427:d3ff:fed6:db42/64 Scope:Link
inet6 addr: fd58:b874:1131::1/60 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:22 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:2836 (2.7 KiB)
eth0 Link encap:Ethernet HWaddr 12:1A:DA:41:A8:1A
inet6 addr: fe80::101a:daff:fe41:a81a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:42 errors:0 dropped:0 overruns:0 frame:0
TX packets:93 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5548 (5.4 KiB) TX bytes:11295 (11.0 KiB)
Interrupt:5
eth0.1 Link encap:Ethernet HWaddr 12:1A:DA:41:A8:1A
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:3541 (3.4 KiB)
eth0.2 Link encap:Ethernet HWaddr D6:27:D3:D6:DB:43
inet addr:192.168.0.134 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::d427:d3ff:fed6:db43/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:42 errors:0 dropped:0 overruns:0 frame:0
TX packets:58 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4792 (4.6 KiB) TX bytes:5856 (5.7 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:66 errors:0 dropped:0 overruns:0 frame:0
TX packets:66 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:5160 (5.0 KiB) TX bytes:5160 (5.0 KiB)
According to this page https://wiki.openwrt.org/doc/uci/wireless
QuoteBy default the wireless is OFF. You can turn it on in the /etc/config/wireless by changing disabled 1 to disabled 0
I can't understand how could I access wifi at the first time.
Anyway It's cleared.