Hi.
I`v got problem with boot Linux from SD card.
Allays I`v got this same info in UART.
When Times goes to 0 reboot again and again...
I use this same SD card in my RSPI (ADATA 16GB class 10). I my RSPI I do not have problem with boot etc.
Can someone tell What I doing wrong?
U-Boot 2014.04-10681-g78592f1-dirty (Jun 06 2014 - 13:43:24) Allwinner Technolog y
CPU: Allwinner A13 (SUN5I)
Board: A13-OLinuXinoM
I2C: ready
DRAM: 512 MiB
MMC: SUNXI SD/MMC: 0
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
reading uEnv.txt
** Unable to read file uEnv.txt **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
reading boot.scr
** Unable to read file boot.scr **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
reading script.bin
29588 bytes read in 30 ms (962.9 KiB/s)
reading uImage
4321416 bytes read in 303 ms (13.6 MiB/s)
## Booting kernel from Legacy Image at 48000000 ...
Image Name: Linux-3.4.90+
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4321352 Bytes = 4.1 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
<6>Booting Linux on physical CPU 0
<6>Initializing cgroup subsys cpuset
<5>Linux version 3.4.90+ (root@debian) (gcc version 4.7.1 (Debian 4.7.1-7) ) #11 PREEMPT Thu Jun 5 16:40:24 EEST 2014
CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: sun5i
<6>Memory Reserved:
<6> SYS : 0x43000000 - 0x4300ffff ( 64 kB)
<6> VE : 0x44000000 - 0x48ffffff ( 80 MB)
<6> LCD : 0x49000000 - 0x4affffff ( 32 MB)
Memory policy: ECC disabled, Data cache writeback
<6>sunxi: Allwinner A13 revision B (AW1625/sun5i) detected.
<7>On node 0 totalpages: 131072
<7>free_area_init_node: node 0, pgdat c08cdd64, node_mem_map d0000000
<7> DMA zone: 512 pages used for memmap
<7> DMA zone: 0 pages reserved
<7> DMA zone: 65024 pages, LIFO batch:15
<7> Normal zone: 512 pages used for memmap
<7> Normal zone: 65024 pages, LIFO batch:15
<7>pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768<c>
<7>pcpu-alloc: <c>[0] <c>0 <c>
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
<5>Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait loglev el=8 panic=10
<6>PID hash table entries: 2048 (order: 1, 8192 bytes)
<6>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
U-Boot SPL 2014.04-10681-g78592f1-dirty (Jun 06 2014 - 13:43:24)
Board: A13-OLinuXinoM
DRAM: 512 MiB
CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
U-Boot 2014.04-10681-g78592f1-dirty (Jun 06 2014 - 13:43:24) Allwinner Technolog y
CPU: Allwinner A13 (SUN5I)
Board: A13-OLinuXinoM
I2C: ready
DRAM: 512 MiB
MMC: SUNXI SD/MMC: 0
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 3
Best Regards
Bartłomiej Kubik
You'll need to provide full info like which image, power supply etc.
John
HI.
Image is from OLIMEX side A13-SOM-512 Debian Linux with kernel 3.4.90+, Power is 3,3V 1A. Specify what information yet i have to tell?
Best Regards
Bartłomiej Kubik
One of corrupt download / poor SD / poor power?
Maybe someone will post or has already posted (googled it?) what the output should be so you can see where it goes wrong.
John
Hi.
I thing problem was resolved.
My Power Cable is too thin and can not send too much peak current.
I've changed power cable and board is running.
Thx for Help:)
Best Regards
Bartłomiej Kubik
Good to hear!
John
Power supply was a problem for me when I started. I did not recognise that and about to send it (a13 board) back. Then I found an old 3.3v 2a supply and it worked :D . Even with USB power supply i.e. 5v 2amp throu 'WiFi board' did not work. :-[