I have been trying to install Debian on Cubieboard's 2 NAND but i only get errors. Is there some specific procedure to do this? what could be wrong?. This is the log of the serial console:
=> FES:
FES:Fes Ver: 098
FES:=================================================================================================
FES:= =
FES:= EEMMMMMMLL =
FES:= ::MMMHOLIGANEE =
FES:= ::MM. =
FES:= MMFF =
FES:= FFMM =
FES:= MMMM =
FES:= ..MMFF =
FES:= EEMM. FFMMMM =
FES:= . MMMMMMMM MMMMMMMMMMMMMMMMMM FFMMMMMM:: ::MMMM BBMMMMFF =
FES:= ::MM . MMMM MMMM MM. MMMMMM EE..EEMM:: EE:: =
FES:= MM MMMM ::MMLL EEMM MMMMFF . MMMM:::: =
FES:= MMMM FFMMI BBMM MMI MMMM MMMMEE =
FES:= MMMM . MM:: MMMM MMMM BBMM MMMM =
FES:= BBMMFF::EE MMMM MMMM MM:: BBMM.. =
FES:= MMMMEE I MMI I MMMM:: ::FFMMFF =
FES:= MMMM LL MMMM EEMMMM LL BB MMMM =
FES:= MMMM I MM MMMM MMMMMM MM:: MM MMMM =
FES:= MMMMMMMMMMEE MMMM .GUANLI@HUANG. BB BB FFMM. =
FES:= MMMMMM.. I MMI MMMMMMEE MMMMMM MMEE =
FES:= MMMM MMMM =
FES:= MMMM ::MM:: =
FES:= MM BBMM MM =
FES:= EEBB BBMM.. MMMM =
FES:= MM ..EEMMFF =
FES:= MMMMMMMMMMMM =
FES:= MMMMMMMMI =
FES:= =
FES:=================================================================================================
FES:INFO : ......1........
FES:INFO : ......2........
FES:INFO : ......3........
FES:INFO : ......5........
FES:INFO : ......6........
FES:INFO : ......7........
FES:INFO : ......8........
FES:INFO : ......9........
FES:CONFIG_USB_GADGET_DUALSPEED
FES:fes connect to host
FES:USB_MOV_DATA_BY_DMA!
FES:INFO : ......10.......
FES:jump to fes_main
FES:INFO: fes_protocol_process start
FES:[info]: set address 24
FES:write special pipe
FES:INFO: fed reg_addr = 0x4011f714
FES:fed para[0] = 0x40900000
FES:fed para[1] = 0x00000000
FES:fed para[2] = 0x00000000
FES:fed para[3] = 0x00000000
[Fed]:-------------------------------------------------
[Fed]: Hello, Nand Register
[Fed]:-------------------------------------------------
[Fed]:"private" part NOT configured.
NHW : start nand scan
[NAND] nand driver(b) version: 0x2, 0x12, data: 20130325
NFC Randomizer start.
[SCAN_DBG] Nand flash chip id is:0x0 0x0 0x0 0x0 0x0 0x8
[SCAN_ERR] search nand physical architecture parameter failed!
NHW : nand scan fail
[Fed]:Fail in NAND_HWScanStart.
[Fed]:Fail to erase flash!
[Fed]:-------------------------------------------------
[Fed]: Byebye, Nand Register.
[Fed]:-------------------------------------------------
FES:INFO : run addr = 0x00000000 , type = 1437204482
http://www.cubieforums.com/index.php/board,25.0.html
You should make sure, you have an image, which is meant for livesuite. This tool has a special format.