Hello,
I have problem with my OLIMEXINO-NANO (https://www.olimex.com/Products/Duino/AVR/OLIMEXINO-NANO/open-source-hardware) (ATMEGA32U4 Arduino Leonardo compatible). I have Windows 64bit. I have this hardware for 5 days and I installed software and drivers properly, because I haven't got any problems with uploading earlier. After this few days I wanted to launch hardware, but operating system found only COM4 (Arduino Leonardo bootloader) and he can't find COM5 (Arduino Leonardo). I was looking for a help in FAQ and I found that if internal LED hasn't blinked after Reset it means there is something bad with bootloader. Below you can find information from software why he can't upload my sketch:
avrdude: Version 6.0.1, compiled on Apr 15 2015 at 19:59:58
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2009 Joerg Wunsch
System wide configuration file is "D:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"
Using Port : COM4
Using Programmer : avr109
Overriding Baud Rate : 57600
AVR Part : ATmega32U4
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 9000 9000 0x00 0x00
flash 65 6 128 0 yes 32768 128 256 4500 4500 0x00 0x00
lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : butterfly
Description : Atmel AppNote AVR109 Boot Loader
Connecting to programmer: .
Found programmer: Id = "CATERIN"; type = S
Software Version = 1.0; No Hardware Version given.
Programmer supports auto addr increment.
Programmer supports buffered memory access with buffersize=128 bytes.
Programmer supports the following devices:
Device code: 0x44
avrdude: devcode selected: 0x44
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% -0.00s
avrdude: Device signature = 0x1e9587
avrdude: reading input file "D:\Users\reV\AppData\Local\Temp\build1786759938084861841.tmp/sketch_may19b.cpp.hex"
avrdude: writing flash (4252 bytes):
Writing | avrdude: ser_send(): write error: sorry no info avail
Anyone had a similar problem? What should I do to launch my Arduino?
Install Linux.